● Knowledge · 23 Replaceability

Replaceable batteries from 2027: who must be able to swap them

From 18 February 2027, Article 11 of the EU Battery Regulation applies: replaceable batteries become mandatory. End-users must be able to swap the battery of a device themselves, while the battery of an e-bike must be replaceable by independent professionals, right down to the cell. Since 11 November 2026 eight exemptions have been law. This guide sorts it out from primary sources and shows which digital battery passport data a workshop needs.

By Grigor Muradyan · Reading time approx. 12 min · Updated: · Not legal advice
18.02.27
Article 11 applies
For devices placed on the market from then
8
exemptions
Art. 11(2), in force since 11 Nov 2026
5 years
spare battery
From the last unit of the model
Cell
LMT swap depth
By independent professionals, Art. 11(5)
In brief
  • Two rules, two addressees. From 18 Feb 2027 end-users must be able to remove and replace portable batteries themselves - the whole battery, with commercially available tools. Batteries in e-bikes and e-scooters must be replaceable by independent professionals, down to the single cell.
  • Eight exemptions have been in force since 11 November 2026. Delegated Regulation (EU) 2026/1770 widened the list from 2 to 8 product groups. Smartphones and tablets follow their own ecodesign rules, and power banks are not covered by Article 11 at all.
  • Proposals are not yet law. Module instead of cell level for LMT batteries and, under the Council's mandate, Article 11 not applying until 18 Aug 2028 to the product groups newly exempted by Regulation 2026/1770 sit in the battery omnibus, which is not adopted on 17 Nov 2026. Plan with the text in force.
  • For LMT batteries the battery passport becomes the workshop file. Part numbers, dismantling information and safety measures sit in Annex XIII point 2, the state of health in point 4. Who may access them is set by an implementing act that is still a draft.
01 · Legal frame

Replaceable batteries: what Article 11 requires from 2027

Article 11 of Regulation (EU) 2023/1542 applies from 18 February 2027 under Article 96(2)(a); until then, Article 11 of the old Battery Directive 2006/66/EC continues to apply. The duty falls not on the battery maker but on whoever places a product with a built-in battery on the market.

ParagraphConcernsWhat applies
Art. 11(1)Products with a portable batteryEnd-users can readily remove and replace the whole battery throughout the product's lifetime; instructions and safety information come with the product and stay online permanently.
Art. 11(2)Eight product groupsReplacement may be reserved to independent professionals.
Art. 11(3)Products needing a permanent connectionParagraph 1 does not apply where safety or data integrity requires a permanent connection.
Art. 11(4)CommissionMay extend the list in paragraph 2 by delegated act.
Art. 11(5)Products with an LMT batteryBattery and every cell in the pack removable and replaceable by independent professionals.
Art. 11(6)Both'Readily replaceable' means substitutable by a compatible battery without affecting functioning, performance or safety.
Art. 11(7)BothSpare batteries for at least five years after the last unit of the model, at a reasonable price.
Art. 11(8)BothSoftware must not impede replacement with a compatible battery.
Art. 11(9)CommissionGuidelines for harmonised application.

An end-user, per the Commission guidelines, is an adult without specific experience or qualification. The Regulation itself does not define independent professionals, only the "independent operator" in Article 3(1)(23). The guidelines fill the gap: independent operators with the technical competence and qualification to repair the product who work on a commercial basis. Proof can be an official repairer register or training by the manufacturer.

02 · Decision path

End-user or professional: the path in six questions

Whether replaceable batteries are required, and who must be able to swap them, follows from a fixed order. The first question that applies tells you your duty.

Who must be able to replace the battery? Six questions under Article 11
  1. Is the battery an industrial, electric-vehicle or SLI battery?
    Art. 11 covers portable and LMT batteries onlyNo, continue ↓
    Yes →Article 11 does not applyOther duties of the Regulation remain
  2. Is the product itself the battery - a power bank, a charging case for earbuds or hearing aids, a jump starter?
    Guidelines C/2026/5531, section 2No, continue ↓
    Yes →Article 11 does not applyThe product is itself a portable battery
  3. Does the battery power a light means of transport such as an e-bike or e-scooter?
    Art. 11(5)No, continue ↓
    Yes →Independent professionalBattery and every single cell
  4. Is the product a smartphone, a mobile or cordless phone, or a tablet?
    Reg. (EU) 2023/1670, Annex II · guidelines section 2.2No, continue ↓
    Yes →Ecodesign rules prevailLayman or, on conditions, a workshop
  5. Does the product need a permanent connection to the battery - for safety, or because collecting data is its main function?
    Art. 11(3)No, continue ↓
    Yes →No replaceability duty under (1)A permanent connection stays allowed
  6. Does the product fall under one of the 8 derogations, and is it needed for safety?
    Art. 11(2) as amended by Reg. (EU) 2026/1770No, continue ↓
    Yes →Independent professionalWhole battery, commercially available tools
  7. All 6 questions answered with no
    Art. 11(1)
    End-userWhole battery, commercially available tools
Decision path for replaceable batteries under Article 11 of Regulation (EU) 2023/1542 as amended by Delegated Regulation (EU) 2026/1770, read with guidelines C/2026/5531. The first question answered with yes decides.

Whether a product falls under Article 11 at all depends on the battery category, explained in Battery models & application classes.

03 · Exemptions

The eight exemptions of Regulation 2026/1770

Delegated Regulation (EU) 2026/1770 of 14 July 2026 was published in the Official Journal on 22 October 2026 and has been in force since 11 November 2026; Article 11 as a whole applies from 18 Feb 2027. It replaces paragraph 2 in full. Replaceable batteries remain mandatory here too, but for the products on the list a swap by independent professionals is enough.

PointProduct groupOnly where needed for safetyStatus
aWashable or rinseable wet appliances, now expressly including wearablesYeswidened
bProfessional medical imaging and radiotherapy devices, in vitro diagnostic devicesNosince 2023
cWearables too small for a safe swap or relying on a sealed enclosureYesnew
dElectric toys with rechargeable batteries - until 31 Jul 2030Yesnew
eWireless thermometer probes in contact with foodYesnew
fEquipment for explosive atmospheres (Directive 2014/34/EU)Yesnew
gOn-body systems for subcutaneous drug deliveryYesnew
hRoof-mounted telematics for agricultural and construction machineryYesnew

For wet appliances the guidelines set five indicators that must all be met: the appliance is designed specifically and primarily for the wet environment, it is washable or rinseable, the product documentation shows a safety risk if end-users replace the battery, and it shows that a redesign is not possible with the state of the art. As a guide, splashing water equals IPX4, water jets IPX5 and IPX6, immersion IPX7 - but the IP rating alone is not sufficient proof.

An exemption is no licence for glued batteries

On the list, too, the battery must stay replaceable - by professionals instead of end-users. Except for the medical devices in point b, every exemption also applies only where it is required for the safety of the user and the appliance.

04 · Special cases

Smartphones, power banks and always-on devices

Three product groups are often misclassified; each has its own rule outside paragraph 2.

Smartphones and tablets
The ecodesign rules of Regulation (EU) 2023/1670 prevail. Since 20 June 2025: layman replacement with basic tools, or workshop replacement with commercially available tools if the battery holds 83 % after 500 cycles and 80 % after 1,000 cycles and the smartphone is dust-tight and watertight at one metre for 30 minutes; for tablets IP42 is enough.
Annex II Reg. 2023/1670
Power banks and charging cases
If a product's main function is to power other products, the guidelines treat it as a portable battery itself. Power banks, charging cases for earbuds or hearing aids and jump starters are therefore not covered by Article 11 at all.
Guidelines C/2026/5531
Permanent connection for safety
Paragraph 3 exempts products that need an uninterrupted power supply. The guidelines name implants, certain in vitro diagnostic devices, hearing aids and smoke alarms with a battery life of at least ten years.
Art. 11(3)
Permanent connection for data integrity
Only where data collection is the main function and data loss is at stake: weather stations, laboratory devices, backup batteries for volatile memory and clocks, toll devices, payment terminals. A device with non-volatile memory does not qualify.
Art. 11(3)
05 · Tools

Readily removable: which tools are allowed

Whether a device has replaceable batteries within the meaning of Article 11 depends on the tools needed. The guidelines translate that into the four tool classes of standard EN 45554.

Which tools a replaceable battery may require
  • No tool or basic toolsIncluding tools supplied with the product or the spare part
    EN 45554 · class iAllowed
  • Commercially available toolsAnyone can buy them on the open market
    EN 45554 · class iiiAllowed
  • Product-group-specific (specialised) toolsNot on open sale, not patented - allowed only if supplied free of charge
    EN 45554 · class iiOnly if supplied free
  • Proprietary toolsNot on open sale, or patent not licensable on fair terms
    EN 45554 · class ivExcluded
  • Thermal energyFor example hot air to release an adhesive bond
    Art. 11(1), 2nd subpara.Excluded
  • SolventsFor example to dissolve glue
    Art. 11(1), 2nd subpara.Excluded
2 allowed · 1 conditional · 3 excluded
For LMT batteries the yardstick is the professional: where more than commercially available tools are needed, they should be available at a reasonable, non-discriminatory price (guidelines, section 2).
Tool classes of EN 45554:2020 as the Commission guidelines apply them to Article 11. 'Commercially available' in the Regulation covers classes i and iii; the legal text itself rules out thermal energy and solvents.

Tools come with an information duty: instructions and safety information on use, removal and replacement accompany the product, and both stay permanently online on a public website in an easily understandable form. The guidelines also recommend listing the specifications a compatible replacement battery must meet and explaining how to dispose of the old one.

06 · LMT batteries

E-bike batteries: professionals, cell level and the battery passport

For LMT batteries paragraph 5 applies: independent professionals must be able to remove and replace the battery and every cell in the pack at any time. From the same day, exactly these batteries also need a battery passport.

1
Compatible cell

A replacement cell is compatible if it does not make the pack unsafe and has the same technical parameters - capacity, state of health, design and chemistry.

2
Tools at fair prices

If a professional needs more than commercially available tools, they should be available at a reasonable, non-discriminatory price.

3
Type-approved vehicles

For type-approved L-category vehicles, professionals are the independent operators within the meaning of Regulation (EU) No 168/2013; the swap must not affect the type approval.

An e-bike battery in the workshop: the passport data each step needs
Workshop stepData from the battery passportReference
Assess the conditionPerformance and durability values, state of health (SoH), charge cycles, events such as accidentsAnnex XIII pt 4(a)Annex XIII pt 4(b)Annex XIII pt 4(d)
Open and dismantle the packExploded diagram, disassembly sequence, fastening techniques, required tools, warnings, number and layout of cellsAnnex XIII pt 2(c)
Source a compatible cellDetailed composition of cathode, anode and electrolyte, part numbers and sources for spare partsAnnex XIII pt 2(a)Annex XIII pt 2(b)
Work safelyThe manufacturer's safety measuresAnnex XIII pt 2(d)
Update the passportBattery status and new values after the change in status - for offline batteries at the service visitAnnex XIII pt 4(a)Annex XIII pt 4(c)
All of these fields sit in the part for persons with a legitimate interest. Who qualifies is set by an implementing act under Art. 77(9) - still a draft on 17 Nov 2026.
Repair or remanufacturing? Two example cases under Art. 3(1)(32)
Case A · one faulty cell swapped for a matching used cell
  • All cells and modules disassembled and evaluatedmissed
  • Capacity 86 % of the original (threshold 90 %)missed
  • SoH spread 3 percentage points (at most 3)met
  • Same purpose as originally designedmet
Definition not met: the passport stays, the swap is recorded (Commission FAQ 9.2)
Case B · every cell tested, weak ones replaced, pack rebalanced
  • All cells and modules disassembled and evaluatedmet
  • Capacity 93 % of the original (threshold 90 %)met
  • SoH spread 2 percentage points (at most 3)met
  • Same purpose as originally designedmet
Remanufacturing: a new passport, linked to the previous one (Art. 77(7))
Annex XIII fields mapped to the steps of a cell replacement under Article 11(5). The case values are illustrative. Art. 3(1)(32) does not say whether the maximum 3 % state-of-health difference means percentage points or a relative difference; the remanufacturing case stays below it under both readings.

The data a workshop needs for a cell swap sits in the part of the passport reserved to persons with a legitimate interest; Article 77(2) expressly names repairers, remanufacturers, second-life operators and recyclers. Who exactly may access it was to be set by an implementing act by 18 Aug 2026; the Commission put it out for feedback as a draft in October 2026. The three access levels are explained in What data goes into the battery passport?, the path of the state of health from the battery management system into the passport in BMS telemetry in the battery passport.

Module level is proposed, not adopted

Commission proposal COM(2025) 981 of 10 Dec 2025 replaces cells with modules in paragraph 5, because an improper cell swap creates safety risks. On 17 Nov 2026 procedure 2025/0397(COD) is awaiting the environment committee's decision. The Council backs the module level in its negotiating mandate of 24 Jun 2026 (Council document 11147/26). Until the text changes, the wording with cells applies, and it governs the design of a pack placed on the market from 18 Feb 2027.

07 · Spare parts

Spare batteries for five years, no parts pairing

Replaceable batteries only help if a spare exists and the software accepts it - paragraphs 7 and 8 see to both.

Whoever places a product with a portable or LMT battery on the market must offer the battery as a spare part for at least five years after the last unit of the model, at a reasonable and non-discriminatory price for professionals and end-users. Where fasteners are not reusable, the guidelines say they belong with the spare part. An often-missed consequence for LMT makers: a spare e-bike battery is itself an LMT battery (Art. 3(1)(11)). Once it is first made available on the Union market, i.e. placed on the market (point 16), from 18 Feb 2027, Article 77(1) requires its own battery passport. The regulation has no exception for spare parts - the duty runs throughout the spare-part period.

Paragraph 8 bans software that impedes replacement with a compatible battery. The guidelines give parts pairing as the example: a serialised spare part is bound by software to one individual device and does not work, or works only partly, after the swap. A notice that a non-original battery is fitted remains allowed as long as it restricts no function.

08 · Timeline

What applies and what is only proposed

Around the rules on replaceable batteries sit a legislative procedure, a draft implementing act and the right-to-repair directive; only part of it has legal effect.

Replaceable batteries: what applies and what is only proposed
Status checked on 17 Nov 2026
  1. 10 Jan 2025
    First guidelines on Article 11
    Notice C/2025/214: tool classes, wet appliances, independent professionals, parts pairing.
    Guidance
  2. 10 Dec 2025
    Commission proposes module level
    COM(2025) 981: LMT batteries replaceable at module rather than cell level. Not adopted.
    Proposal
  3. 31 Jul 2026
    Right to repair applies
    Directive (EU) 2024/1799, Annex II point 10: goods with an LMT battery fall under the manufacturer's obligation to repair.
    In force
  4. 22 Oct 2026
    New derogations and guidelines in the Official Journal
    Delegated Regulation (EU) 2026/1770 and Notice C/2026/5531.
    Official Journal
  5. 11 Nov 2026
    New list of derogations in force
    Article 11(2) is replaced, 20 days after publication.
    In force
  6. 16 Nov 2026
    Feedback deadline for the access-rights act
    Draft under Art. 77(9): who may see the restricted passport parts. The act was due by 18 Aug 2026.
    Draft
  7. 14 Dec 2026
    Plenary on the battery omnibus (indicative)
    Procedure 2025/0397(COD) awaits the committee decision. The Council wants Article 11 not to apply until 18 Aug 2028 to the product groups newly exempted by Regulation 2026/1770 (mandate of 24 Jun 2026, Council doc. 11147/26).
    Proposalin 27 days
  8. 18 Feb 2027
    Article 11 applies
    The same day the battery passport becomes mandatory for LMT, industrial and EV batteries.
    Deadlinein 93 days
  9. 31 Jul 2030
    Toy derogation expires
    Point d lapses; from then the Toy Safety Regulation (EU) 2025/2509 governs battery access.
    Expiresin 1352 days
Worked example: the spare-battery window under Art. 11(7)
Last unit of the model placed on the market30 Jun 2029
Spare batteries at least until (5 years)30 Jun 2034
Date chosen freely. Every spare e-bike battery placed on the market in this window is itself an LMT battery.
Legal status of Article 11 and its surroundings. Dashed entries are drafts or proposals without legal effect. Days to future dates are counted from the check date.

Through Annex II point 10 of Directive (EU) 2024/1799, the right to repair also hangs on Article 11: for goods with an LMT battery the manufacturer must repair at the consumer's request, to the extent the Battery Regulation sets repairability requirements. Member States have applied their transposition since 31 Jul 2026.

09 · In Batteriepasswerk

What our product covers - and what it does not

Whether a product has replaceable batteries is decided by the design, not by software. We cover the passport side of Article 11 for LMT batteries.

A view for workshops
The QR code resolves to different views depending on who asks. The view for recyclers, remanufacturers and workshops contains dismantling information, detailed composition and repair information. Which persons qualify is only settled by the implementing act.
Access levels
A swap as a repair event
Installed components can be recorded per passport by serial number. A swap is logged as a repair and the passport stays the same - also via REST API straight from the service system.
Lifecycle
A successor passport after remanufacturing
If an intervention meets the definition of remanufacturing, a wizard creates the new passport and chains it to the previous one, as Article 77(7) requires. Every version stays hash-protected.
Art. 77(7)
One passport per spare battery
Spare batteries for service are units like any other: create the model once, serial numbers by CSV or API, one GS1 Digital Link QR code per unit.
Serialisation

What we do not cover

Design, tool choice, end-user instructions and spare-part logistics under Article 11 remain the job of product development. Portable batteries need no battery passport, so our software does not help there. Whether a specific product falls under an exemption is a legal question for the individual case.

Your role when placing on the market: Economic operators of the Battery Regulation. What else the battery passport means for e-bike and e-scooter makers: Battery passport for light means of transport.

10 · FAQ

Frequent questions on replaceable batteries

Do phone batteries have to be replaceable from 2027?
For smartphones and tablets, the Commission guidelines say the ecodesign rules of Regulation (EU) 2023/1670 prevail over Article 11. They have applied since 20 June 2025: either a layman swaps the battery with basic tools, or a workshop does it with commercially available tools. In the second case the battery must keep 83 % of its capacity after 500 cycles and 80 % after 1,000 cycles; a smartphone must also be dust-tight and survive 30 minutes at one metre of water, a tablet must reach at least IP42.
Does the rule apply to devices sold before 2027?
No. Article 11 applies from 18 February 2027 and is tied to placing on the market. A device placed on the market before that date does not have to be retrofitted; for the spare-part duty the Commission guidelines say so expressly. What counts is the individual unit, not the model: a device first placed on the market from the deadline onwards must comply, even if the model has been on sale for years.
Which devices are exempt from battery replaceability?
Since 11 November 2026, Article 11(2) lists eight product groups whose battery only needs to be replaceable by independent professionals: wet appliances including wearables, medical imaging and in vitro diagnostics, small or sealed wearables, electric toys until 31 July 2030, food thermometer probes, equipment for explosive atmospheres, on-body drug delivery systems and roof-mounted telematics for agricultural and construction machinery. Paragraph 3 fully exempts products that need a permanent battery connection for safety or data reasons.
What does 'commercially available tools' mean?
The battery must come out without specialised tools, proprietary tools, thermal energy or solvents. The Commission guidelines draw on standard EN 45554: no tools, basic tools and tools anyone can buy are allowed. A product-group-specific specialised tool is only acceptable if it is supplied free of charge with the product. A glued battery that only comes out with a heat gun does not meet the requirement.
Must users be able to replace an e-bike battery themselves?
Article 11 does not require that for LMT batteries. Paragraph 5 requires that independent professionals can remove and replace the battery and every single cell in the pack throughout the product's lifetime. The Commission has proposed replacing the cell level with the module level (COM(2025) 981). On 17 November 2026 that is not adopted; until it changes, the wording with cells applies.
How long must spare batteries be available?
For at least five years after the last unit of the equipment model was placed on the market, at a reasonable and non-discriminatory price for independent professionals and end-users (Article 11(7)). As guidance, the Commission points to ecodesign rules that require delivery within five working days of the order. For smartphones and other mobile phones, Regulation (EU) 2023/1670 already requires seven years.
Does an e-bike battery need a new battery passport after a cell swap?
Usually not. According to the Commission FAQ, a simple repair does not require a new passport; the existing one is updated, for batteries without connectivity at the service visit. Article 77(7) requires a new passport, linked to the old one, only after remanufacturing: every cell disassembled and evaluated, at least 90 % of the original capacity restored and the cells' state of health within 3 % of each other.
11 · Sources

Sources & further reading

Replaceable and documented

The battery passport for LMT batteries that workshops can actually repair

Batteriepasswerk serialises every unit, spare batteries included, records repairs in the lifecycle and chains the successor passport after remanufacturing - conformant to EU 2023/1542, hosted in the EU.